So many ideas just like " How to making AAC product in manufacturing "
Just simple THINK,
- Have the machine - not to high technology - simple machine
- Have the sources of material i,e Sand ( silica ) , Fly ash, or Bottom Ash, Quicklime,
cement and some ingredient i,e Anhydrate, Raising Agent.
- Have the Cooking - ( production people )
- Have the good recipe.
- Have the Market or Internal market
- Have the strategies - Location
- Infrastructur
Finally Just Do It : 2MOC
M = Market
M = Have mechanical
O = Operational
C = Chemical or additive
And got the bread as Aerated Autoclave Concrete
We’re representatives of Kalmatron Corporation manufacturer of Concrete Class Upgrading Admixtures, Remedial Coats, and Concrete Regenerative Sprays.
ReplyDeleteBoth of products are registered in International Sanitary Fund with tests reports from four continents. www.kalmatron.com
We have favorable prices with free ocean freight and discounts. Sampling is available also.
NRD Industries
USA
E-mail : nrdindustries@gmail.com,
Skype ID: dilipshah26
Dr. Alex Rusinoff
Visit us at:
www.greenbuiltconcrete.com NEW!
www.drivewayoverlay.com NEW!
LIGHTWEIGHT CONCRETE
Attached is one of hundreds mix designs what was developed during of last 12 years.There are many variations with Fly Ash, Expended Shell, Polystirol, etc could be there.
For presentation only
• LIGHTCRETE – III, 24 MPa •
Material Quantities Quantities Notices
(Kg) (m3)
Portland Cement CEM I 32,5 R 200 0.03
Gypsum 200 0.150
Coarse Sand 100 0.043 Any available Coarse Sand
Water Liters 108 0.104 W/C=0.27
Voids Foaming Agent 0.914 0.602 Use any available for concrete
application.
Fiber/Polyvinyl fiber strings 3 n/a ∅ 0.5 mm: Length ~ 2 cm.
K1OO® A 10 0.0062 K1OO® by 2 Liters 1m3 is as an
option to K1OO® A
Total: 622 0.9682 Wet Density is at 643 Kg/m3
BATCH INSTALLATION
MIX PREPARATION
1. Mix batch’ ingredients for 3 minutes without Voids Foaming Agent.
2. Cementitious Slurry blend should appear.
ENTRAINMENT OF VOIDS FOAMING AGENT
1. Apply Voids Foaming Agent into the cementitious slurry during mixer rotation.
2. Mixing time should not be less than at 4 to 7 minutes.
3. Do not apply any other additives, chemicals or supplementary materials.
4. Check batch density by 643÷670 [Kg/m3].
CURING
1. At the experimental stage cure for 2 hours in a standard camera, unmold afterwards.
2. Curing time without camera must be at ¾ from the standard.
3. For the next batch do not provide curing. Unmold after 4 hours.
4. Compare by the final cutting both of materials.
EXPECTED RESULTS
1. No shrinkage cracks, flakes, efflorescence, curling, and edges fragility.
2. Liquid impermeability is W6 for at 100 mm thick LIGHTCRETE III slab.
3. Highest resistance to chemical and climate corrosions.
Testimonial mix volume should not be less than 124 Kg. Smaller batches are not effective for complete design performance.
KALMATRON® CORPORATION
• This information is an intellectual property of the KALMATRON® Corporation and any attachments are confidential, may contain privileged sources and are protected by the contents of the International patents, trademarks, and copyrights laws.
• You notified that any publicity, distribution, dissemination, reformatting, or copying is prohibited and will be prosecuted under the International Laws of Patent & Trademark Offices on every given Territory.